View

 

 

The author is making a number of great points on the subject of Tools You Need to Install a New Bathtub overall in the article further down.

Installing a bath tub isn't specifically rocket science, but it does call for solid plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is additionally a moderately difficult task. If the old tub is readily easily accessible, the project can relocate rapidly; if you have to open up a wall to get rid of the old tub as well as position the new tub, the job is a lot harder. In either case, the task is within a house handyman's skills, although you will certainly need an assistant to move out the old bathtub and also set in the new one. Make certain you have certified yourself for the task and fit attempting it. As opposed to hiring a service provider to take over a halfway-completed task, it is better to take into consideration utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This post will certainly assist you mount a new bath tub in your restroom if you have actually already gotten a brand-new tub and also don't require to transform the arrangement of your previous water pipes.
Your tools and also material list must comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Removing Old Taps

If you need to change old taps with new ones as a part of your setup, after that the first thing you ought to do is detach the water. After doing so, turn on the taps to drain pipes any water remaining in the system. The procedure of getting rid of the existing taps can be quite troublesome as a result of the restricted accessibility that is often the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly originate from the pipes. When the supply pipelines have actually been removed, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from transforming throughout this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Prior to moving on to fit the new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the new taps to fit.

 

 

Suitable New Touches

If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will need minimizing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in area in between the faucet as well as the sink. Protect the tap in place with the manufacturer provided backnut. Once the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet adapters. The previous type ought to be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.

 

 

Installing the Tub

Utilizing the two wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are useful in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 small points.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by checking the spirit level and also changing the feet on the bathtub till the level reads degree.
To set up taps, fit all-time low of the outermost versatile faucet port to the suitable supply pipe by making a compression sign up with; then do the very same for the various other tap.
Turn on the supply of water and examine all joints as well as new pipework for leaks and also tighten them if needed. Fill the bath tub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leakages.
Finally, deal with the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub needs to wait up until the bath tub has been utilized at least once as this will resolve it right into its final setting.

 

 

Preparing for the Installation

First of all, the sustaining frame provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is necessary to make certain that if the tap includes a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets unit to avoid pressure on the tub.
Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you use all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its final setting.

 

 

Tiling Around the Tub

In the location where the bathroom meets the tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture a rigid seal, causing the water to permeate the wall between the bath as well as the tiling, causing difficulties with wetness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, as well as can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water before securing, to permit the activity experienced when the bathtub remains in use. The sealant can break fairly early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As an enthusiastic reader about Installing A Bathtub, I imagined sharing that topic was important. I beg you set aside a second to share this blog post if you appreciated it. Thanks for your time invested reading it.

Book An Estimate Now